竞斗云2R619AC刷机支持usb3.0 竞斗云2R619AC刷opboot及128M nand openwrt固件带V2瑞(带sdcard及usb3.0驱动)
前两天105到手一台,今天试水升级uboot及第三方固件,其实很简单,给需要的同学一个参考.
教程修改为升级OpBoot,之前的uboot功能过于简单,opboot比较强大,可刷入ubi及bin固件,同时可备份编程固件.
目前官方固件已关闭第三方升级通道,以下方法失效.本人提供的固件请在opboot中升级,X-wrt和本固件冲突,切勿在X-wrt中在无opboot的情况下升级,必砖.
以下教程为官方原厂固件刷opboot及OpenWRT教程,其它固件非原厂固件请谨慎.非原厂固件请需刷到原厂固件后参考教程操作,网盘中有原厂固件.
首先原厂固件到系统设置中检测升级到最新固件版本2.5.11.82.
然后选择bootloader解锁固件刷入(文件名openwrt-ipq40xx-R9.11.22-unlock-p2w_R619AC-squashfs-nand-factory.bin)刷入即可,第三方固件刷入完成.
等3min左右,自动开机后登陆192.168.15.1 密码 password.
winscp连接到路由器,将不死opboot(文件名opboot-p2w-r619ac-flash-v1.0.9.bin)上传到/tmp目录下.
ssh到路由器如下命令完成opboot刷入
mtd -r write /tmp/opboot-p2w-r619ac-flash-v1.0.9.bin Bootloader
opboot刷入后会自动重启.
多说一句按住reset键,然后上电进opboot((需按住10S)
竞斗云2刷opboot及128M nand openwrt固件
固件ip地址:192.168.15.1 或http://openwrt.lan
密码:password
wifi名称:Openwrt密码无
Update 2019.12.08
1.同步最新源码
2.更新package ipk打包下载,请参考packagelist.txt.
3.去除百度云(之前无法运行,原因未知)
4.加入aria2与transmission下载
5.加入打印机服务器及samba网络共享功能.
6.加入MWAN,可实现多拨.
7.加入网络流量监控等.
6.后期只会同步源码了,暂时不考虑新增功能.
Update 2019.11.29
1.同步更新lean大最新源码.
2.增加百度网盘,Aria2功能.
3.新增sdcard及USB 3.0驱动,测试正常
4.分享文件增加相关IPK package打包下载(软件清单参照packagelist.txt内容).不打包网盘太容易挂了.
竞斗云2刷openwrt固件下载地址
G-docker opboot&firmware.zip: http://dl.iqqoz.com/file/1397394-414245824
链接: https://pan.baidu.com/s/1YMingTc141jJ18WsaoAT-Q提取码: xwu4
以下是USB 3.0驱动日志
[ 5.712364] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.716553] SCSI subsystem initialized
[ 5.720410] ehci-platform: EHCI generic platform driver
[ 5.723120] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.727537] ohci-platform: OHCI generic platform driver
[ 5.734312] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.043195] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.043351] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 6.048162] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010
[ 6.055261] xhci-hcd xhci-hcd.0.auto: irq 130, io mem 0x08a00000
[ 6.065202] hub 1-0:1.0: USB hub found
[ 6.070822] hub 1-0:1.0: 1 port detected
[ 6.074705] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.078428] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 6.083772] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
网盘文件说明如图
原文：https://www.right.com.cn/forum/thread-1442821-1-1.html
本站附件分享，如果附件失效，可以去找找看
